busel.hvist/breakboard/gerber/pcb_outline.ngc.tap

79 lines
2.0 KiB
Plaintext
Raw Normal View History

2024-08-13 09:31:38 +03:00
( pcb2gcode 2.5.0 )
( Software-independent Gcode )
G94 ( Millimeters per minute feed rate. )
G21 ( Units == Millimeters. )
G90 ( Absolute coordinates. )
G00 S24000 ( RPM spindle speed. )
G64 P0.01016 ( set maximum deviation from commanded toolpath )
G01 F100.00000 ( Feedrate. )
G00 Z5.00000 (Retract to tool change height)
T1
G04 P1.00000 (Wait for spindle to stop)
(MSG, Change tool bit to cutter diameter 3.00000mm)
M3 ( Spindle on clockwise. )
G04 P1.00000 (Wait for spindle to get up to speed)
G04 P0 ( dwell for no time -- G64 should not smooth over this point )
G00 Z5.00000 ( retract )
G00 X76.49997 Y-88.74999 ( rapid move to begin. )
G01 Z-1.60000 F50.00000 ( plunge. )
G04 P0 ( dwell for no time -- G64 should not smooth over this point )
G01 F100.00000
G01 X76.49997 Y-77.49999
G00 Z5.00000
G01 X76.49997 Y-73.99999
G01 Z-1.60000 F50.00000
G01 F100.00000
G01 X76.49997 Y-62.74999
G01 X76.52880 Y-62.45733
G01 X76.61417 Y-62.17595
G01 X76.75278 Y-61.91661
G01 X76.93932 Y-61.68931
G01 X77.16662 Y-61.50277
G01 X77.42596 Y-61.36416
G01 X77.70734 Y-61.27880
G01 X78.00000 Y-61.24997
G01 X227.99998 Y-61.24997
G01 X228.29261 Y-61.27880
G01 X228.57399 Y-61.36416
G01 X228.83332 Y-61.50277
G01 X229.06063 Y-61.68931
G01 X229.24717 Y-61.91661
G01 X229.38577 Y-62.17595
G01 X229.47114 Y-62.45733
G01 X229.49997 Y-62.74999
G01 X229.49997 Y-73.99999
G00 Z5.00000
G01 X229.49997 Y-77.49999
G01 Z-1.60000 F50.00000
G01 F100.00000
G01 X229.49997 Y-88.74999
G01 X229.47114 Y-89.04262
G01 X229.38577 Y-89.32400
G01 X229.24717 Y-89.58334
G01 X229.06063 Y-89.81064
G01 X228.83332 Y-89.99718
G01 X228.57399 Y-90.13579
G01 X228.29261 Y-90.22116
G01 X227.99998 Y-90.24998
G01 X78.00000 Y-90.24998
G01 X77.70734 Y-90.22116
G01 X77.42596 Y-90.13579
G01 X77.16662 Y-89.99718
G01 X76.93932 Y-89.81064
G01 X76.75278 Y-89.58334
G01 X76.61417 Y-89.32400
G01 X76.52880 Y-89.04262
G01 X76.49997 Y-88.74999
G04 P0 ( dwell for no time -- G64 should not smooth over this point )
G00 Z5.000000 ( retract )
G04 P1.000000
M9 ( Coolant off. )